Customized Consulting


Please provide your correct contact information, and our customer service team will get in touch with you as soon as possible!

Submit
%{tishi_zhanwei}%
Image Name

The role of Hall sensors in brushless DC motors

A Hall current sensor is essentially a sensor based on the Hall effect. When a current-carrying conductor or semiconductor is placed perpendicular to a magnetic field, the resulting measurable voltage is referred to as the Hall voltage.

Date:

Apr 12,2025

Date:

Ruixing Motor


A Hall‑effect current sensor is essentially a sensor based on the Hall‑effect principle. When an electric current flows through a conductor or semiconductor in one direction and a magnetic field is applied perpendicular to that current, the resulting measurable voltage is called the Hall voltage. In short, applying a magnetic field perpendicular to the current flow generates a voltage across the conductor. A Hall‑effect current sensor is a solid‑state device that leverages this principle to determine the position, speed, and various other parameters required for the efficient operation of brushless DC motors. I. Amplified Diagram of a Hall‑Effect Current Sensor: A small current always flows through the Hall‑effect strip. As mentioned earlier, the alternating magnetic field generated by the rotor magnets induces a voltage across the Hall‑effect strip. This voltage is then fed into a digital circuit (as shown in the figure above), and the resulting digital signal serves as the output of the Hall‑effect current sensor. II. How Does a Hall‑Effect Current Sensor Work in a Brushless DC Motor? Typically, a BLDC motor is equipped with three Hall‑effect current sensors mounted on either the rotor or the stator. These sensors are spaced 120 degrees apart, providing angular position information from 0 to 360 degrees. When these Hall sensors detect the rotor’s magnetic field, they generate corresponding digital pulses—logic “1” or “0”—as illustrated below. Through six distinct steps, these Hall sensors can determine the motor’s angular position. In the diagram, the rectangular waveforms depict the positive and negative pulses produced by each of the three Hall‑effect sensors (A, B, and C) at their respective angles. The accompanying chart also shows how, upon reaching 360 degrees, the motor completes one commutation cycle in six steps. The following explanation further clarifies this process: As the rotor magnets pass over each sensor, the sensor outputs a low or high signal depending on whether it detects the rotor’s north or south pole. When the rotor passes all three sensors, the signals switch between low and high states, thereby indicating the rotor’s position every 60 degrees. The figure below illustrates a typical BLDC motor controller, where three lines connecting the motor to the controller represent the signals sent by the three Hall‑effect current sensors. Hall‑effect current sensors can distinguish between positively and negatively charged particles moving in opposite directions. The magnetic field detected by the sensor is converted into an appropriate analog or digital signal that can be processed by the electronic system—usually the motor control system. Below is a truth table derived from readings taken by the three Hall‑effect current sensors. As you can see, the transistor states of the H‑bridge depend on the signals detected by the sensors. Downward arrows indicate clockwise rotation (CW), while upward arrows indicate counterclockwise rotation (CCW). With the truth table and diagrams in hand, it becomes straightforward to calculate the rotor’s angular position and speed. 1. Angle Calculation: Based on the Hall‑effect current sensor signals, as shown in Figure 1, the angle from 0 to 360 degrees is computed using the pulse patterns from the Hall sensors. 2. Speed Calculation: Speed is determined by measuring the period of the Hall‑effect current sensor signals. Using the period, frequency and speed are calculated according to the formula: Frequency = 1 / Period. Only one Hall‑effect sensor is needed to compute speed. III. Advantages of Using Hall‑Effect Current Sensors in Brushless DC Motor Controllers: 1. Hall‑effect current sensors are very simple devices composed primarily of magnets, making them highly cost‑effective for motor control systems. 2. For the same reason, these sensors are easily integrated into advanced motor control systems for electric vehicles and other automotive applications. 3. Most brushless DC motors come equipped with these sensors. 4. Hall‑effect current sensors are largely unaffected by environmental factors such as humidity, temperature, dust, and vibration.


Next article:

Related News

Principles of Weak-Flux Control in Brushless DC Motor Drives and Their Advantages and Disadvantages

2025-04-12


Since brushless DC motors are inductive loads, the phase current lags behind the phase voltage. Consequently, the actual angle between the rotor flux and the stator flux in a permanent‑magnet brushless motor is not 90 degrees; moreover, this error increases as the motor speed rises.

Differences between DC brushless motors and servo motors

2025-04-12


A brushless DC motor consists of the motor itself and a driver, making it a quintessential mechatronic product.

The role of Hall sensors in brushless DC motors

2025-04-12


A Hall current sensor is essentially a sensor based on the Hall effect. When a current-carrying conductor or semiconductor is placed perpendicular to a magnetic field, the resulting measurable voltage is referred to as the Hall voltage.

Please provide your correct contact information, and our customer service team will get in touch with you as soon as possible!

Submit
%{tishi_zhanwei}%